Daikin

From CoolAutomation Wiki
Jump to navigation Jump to search

Setting Indoor Group Address

Indoor Group Address is required for proper CoolMasterNet operation. Without Group Address Indoor unit is not visible and can not be controlled by CoolMasterNet. Group Address is set with wired remote controller. Here is a simple sequence of operations for Daikin BRCE61 wired remote controller to set Group Address.

  • Press and hold Cancel button for a few seconds

BRC1E61-buttons.gif

  • Scroll down to Group No. setting function and press Menu/Enter button

BRC1E61-group-address-menu.gif

  • Program Group Address and then press Menu/Enter to save address

Remember if Indoor unit can not see a CoolMasterNet you won't have the Group Address menu option. So make sure the CoolMasterNet is wired to F1 F2 HVAC line and powered.

Reading Thermostat ambient temperature instead of return air

CoolMasterNet will read ambient temperature measured by Thermostat - local wired controller (like BRC1E72) if following field settings had being done on Thermostat:
Setting 10-2 = 03 - Only the thermostat thermistor will be utilized by Indoor unit.
Setting 10-5 = 02 - Room temperature value reported to CoolMasterNet by Indoor is taken from Thermostat

KRP928A2S Auto Mode Control

To enable proper Auto Mode control from CoolMasterNet of the Indoor Unit connected via KRP928A2S adapter, make sure to configure SW3 switch to GLO position:
KRP928A2S-SW3.png

Daikin Self-diagnostic Malfunction (Error) Codes

I
n
d
o
o
r

U
n
i
t
Malfunction

Code

Problem

Description

Supposed

Causes

Models
RA Sky
Air
VRV Pac
kage
HRV Chil
ler
Fan
Coil
A0 External protection device activated External protection device connected to the terminal strip T1-T2 of indoor unit is activated V V V
A1 Malfunction of indoor unit PCB Defective indoor unit PCB
External factor (Noise etc.)
V V V V V V
A3 Drain Level Control System Abnormality Drain clogging, upward slope, etc
Defective drain pump
Defective float switch or short circuit connector
V V V V V
A4 Malfunction of freezing protection Shortage of water volume
Low water temperature setting
Defective water temperature thermistor
V V V V V V
A5 High pressure control in heating, freeze-up protection control in cooling Clogged air filter of indoor unit and short circuit
Defect of indoor unit heat exchanger thermistor
V V V V
A6 Malfunction of fan motor Broken wires in, short circuit of, or disconnection of connectors from the fan motor harness
Defective fan motor
Defective indoor unit PCB
V V V V V
A7 Malfunction of swing flap motor Defective swing fl ap motor
Defective indoor unit PCB
Defective connection cable
Defective airflow direction adjusting fl ap-cam
V V
A8 Malfunction of power supply or AC input overcurrent Defective power supply voltage
Defective connection on signal line
Defective wiring
V V V
A9 Malfunction of electronic expansion valve Defective electronic expansion valve coil
Defective indoor unit PCB
Defective relay cables
V V V V V
AA Heater overheat 26WH is activated V V
AF Malfunction of a humidifi er system Humidifi er unit (optional accessory) leaking
Defective drain piping (upward slope, etc.)
Defective indoor unit PCB
V V V
AH Malfunction of dust collector of air cleaner Defect of dust collecting element
Stained insulator part
Defect of high voltage power supply unit
Defect of indoor unit PCB
V V V V
AJ Malfunction of capacity setting(Indoor unit PCB) The capacity setting adaptor was not installed when replacing PCB.
Defective indoor unit PCB
V V V
С1 Failure of transmission (between indoor unit PCB and sub PCB) Defective connection of the connector between indoor unit PCB V V
С4 Malfunction of liquid pipe thermistor for heat exchanger Defective thermistor for liquid pipe
Defective indoor unit PCB
Defective connector contact
V V V V V V V
C5 Malfunction of gas pipe thermistor for heat exchanger Defective thermistor for gas pipe
Defective indoor unit PCB
Defective connector contact
V V V V V
C6 Malfunction of fan motor sensor or fan control driver Defective fan PCB
Defective connection of capacity setting adaptor
Field setting error
V V
C7 Front panel driving motor fault Defective front panel driving motor
Defective limit switch
V
C9 Malfunction of suction air thermistor Defective thermistor for suction air
Defective indoor unit PCB
Defective connector contact
V V V V V V
CA Malfunction of discharge air thermistor Defective thermistor for discharge air
Defective indoor unit PCB
Defective connector contact
V V V V
CC Malfunction of humidity sensor system Defective humidity sensor
Defective connector contact
V V V
CJ Room temperature thermistor in remote controller abnormality Defective room temperature thermistor in remote controller
Defective remote controller PCB
External factor (Noise etc.)
V V V V V
H5 Malfunction of compressor motor overload thermistor Defect of compressor motor overload thermistor
Defective connector contact
V V
H6 Malfunction of position detection sensor Faulty contact of compress or cable
Defective compressor
Defective outdoor unit PCB
V V V
H7 Malfunction of outdoor unit fan motor signal Abnormal signal from fan motor (Circuit failure)
Disconnection/Short circuit in fan motor leads or
disconnection of connector
Defective inverter PCB
V V V V
H8 Malfunction of compressor input(CT) system Defective power transistor
Defective reactor
Faulty wiring of inverter system
Defective outdoor unit PCB
V V
H9 Malfunction of outdoor air thermistor Defective connection of thermistor
Defective outdoor unit PCB
Defective outdoor air thermistor
V V V V V
HC Malfunction of (hot) water temperature thermistor Defective connection of thermistor
Defective outdoor unit PCB
Defective water temperature thermistor
V V V
HF Alarm in thermal storage unit or storage controller Thermal storage group defective wiring
Defective setting
Excess of thermal storage tank numbers
V
HJ Malfunction of thermal storage tank water level Low water level
Defective switch setting
Water level detecting sensor failure
Defective connector contact
V V V V
J1 Malfunction of pressure sensor Defective pressure sensor connector contact
Defective pressure sensor
Defective outdoor unit PCB
V V V V
J2 Malfunction of current sensor of compressor Defective current sensor
Defective compressor
Defective outdoor unit PCB
V V V V V
J3 Malfunction of discharge pipe thermistor Defective connection of thermistor
Defective discharge pipe thermistor
Defective outdoor unit PCB
V V V V V
J4 Malfunction of low pressure
equivalent saturated temperature
sensor system
Defective connection of thermistor
Defective thermistor
Defective outdoor unit PCB
V V
J5 Malfunction of suction pipe thermistor Defective connection of thermistor
Defective suction pipe thermistor
Defective outdoor unit PCB
V V V V
J6 Malfunction of heat exchanger thermistor
J7 Malfunction of thermistor (Refrigerant circuit) Defective connection of thermistor
Defective liquid pipe thermistor
Defective outdoor unit PCB
V V V V
J8 Malfunction of thermistor (Refrigerant circuit) Defective connection of thermistor
Defective liquid pipe thermistor
Defective outdoor unit PCB
V V V V V
J9 Malfunction of thermistor (Refrigerant circuit) Defective connection of thermistor
Defective gas pipe thermistor
Defective outdoor unit PCB
V V V V V
JA Malfunction of high pressure sensor Defective connector contact
Connection of low pressure sensor in mistake for high
pressure sensor
Defective high pressure sensor
Defective outdoor unit PCB
V V V V
JC Malfunction of low pressure sensor Defective connector contact
Connection of high pressure sensor in mistake for low
pressure sensor
Defective low pressure sensor
Defective outdoor unit PCB
V V V V
P2 Automatic refrigerant charge operation stop The stop valve is not opened
Closed valve of refrigerant tank
V V V V
P3 Malfunction of thermistor in switch
box
Defective connection of thermistor
Defective reactor thermistor
Defective inverter PCB
V V V V V
P4 Malfunction of radiation fi n
temperature sensor
Defective radiation fi n temperature thermistor
Defective inverter PCB
Defective INV. compressor
Defective fan motor
V V V V V
P8 Heat exchanger freezing protection
during automatic refrigerant
charging
(Close the refrigerant cylinder. Start again from step 1.) V V V
P9 Malfunction of fan motor
(humidifi er unit)
Defective fan motor
Defective outdoor unit PCB
Broken relay harness
Defective connector contact
V
P9 Automatic refrigerant charge
operation completed
V V V V
PA Refrigerant cylinder during
automatic refrigerant charging
Refrigerant cylinder of master unit is empty V V V
PA Broken wire of heater
(humidifi er unit)
Defective heater unit
Defective thermistor
Defective outdoor unit PCB
V
PC Refrigerant cylinder during
automatic refrigerant charging
Refrigerant cylinder of slave unit 2 is empty V V
PE Automatic refrigerant charge
operation nearly completed
V V V
PH Refrigerant cylinder during
automatic refrigerant charging
Defective heater unit
Defective connector contact
Defective thermistor
Defective outdoor unit PCB
V V V
PJ Malfunction of capacity setting
(Outdoor unit PCB)
Capacity setting adaptor is not installed
Improper capacity setting adaptor
Defective outdoor unit PCB
V
PJ Improper combination between
inverter and fan driver
Mis-matching of type of PCB
Improper (or no) fi eld setting after replacing outdoor unit
main PCB
V V V V
U0 Shortage of refrigeran Refrigerant shortage and refrigerant clogging
(wrong piping) Defective thermistor
Defective low pressure sensor
Defective outdoor unit main PCB
V V V V V
U1 Reverse phase, open phase Power supply reverse phase
T phase open phase
Defective outdoor unit PCB (A1P)
V V V V V V V
U2 Malfunction of power supply or
instantaneous power failure
Abnormal power supply voltage
Instantaneous power failure
Defective main circuit wiring
V V V V V V
U3 Check operation not executed or
transmission error
Check operation is not executed. V V V V V V V
U4 Malfunction of transmission
between indoor and outdoor unit
Short circuit in indoor-outdoor or outdoor-outdoor
transmission wiring (F1 / F2), or wrong wiring
Outdoor unit power supply is OFF

System address does not match Defective indoor unit PCB Defective outdoor unit PCB

V V V V V V V
U5 Malfunction of transmission
between indoor unit and remote
controller
Transmission error between indoor unit and remote
controller
Connection of 2 main remote controllers (when using 2
remote controllers)
Defective indoor unit PCB
Defective remote
controller PCB
Transmission error caused by noise
V V V V V V
U6 Malfunction of transmission
between indoor units
Faulty wiring
External factor (Noise etc.)
Defective indoor unit PCB
V V V V
U7 Malfunction of transmission
between outdoor units or outdoor
storage unit
Connection error of transmission wirings between outdoor
unit and external control adaptor for outdoor unit
Connection error of transmission wirings between outdoor
units
Defective outdoor
unit PCB
V V V V V
U8 Malfunction of transmission
between remote controllers
Transmission error between main and sub remote
controller
Connection between sub remote controllers
Defective remote controller PCB
V V V V V V
U9 Malfunction of transmission (other
system)
Transmission error between other indoor and outdoor units
Defective electronic expansion valve of other indoor unit
Defective indoor unit PCB of other indoor unit
Improper connection of
transmission wiring between
indoor and outdoor unit
V V V V V
UA Defect of indoor/outdoor power
supply
Wrong model connections
Improper power supply
Wrong PCB connected
Defective PCB
V
UA Improper combination of indoor
and outdoor units
Excess of connected indoor units
Defective outdoor unit PCB
Mismatch of the refrigerant type of indoor and outdoor unit
Setting of outdoor unit PCB was not carried out after
replacing to
spare PCB
V V V V
UA Remote temperature setting wire
disconnection
Remote temperature setting wire disconnection
Defective connector contact
V
UC Malfunction of setting of centralized
control equipment address
Address duplication of centralized control equipment
Defective indoor unit PCB
V V V V V V
UE Malfunction of transmission
between indoor unit and
centralized control equipment
Transmission error between optional controllers for
centralized control equipment and indoor unit
Connector for setting main controller is disconnected.(or
disconnection of connector for independent / combined
use changeover switch.)
Defective PCB for central remote controller
Defective indoor unit PCB
V V V V V V
UF System is not set yet Improper connection of transmission wiring between
indoor-outdoor units and outdoor-outdoor units
Failure to execute check operation
Defective indoor unit PCB
Stop valve is not opened
V V V V
UH Malfunction of system Improper connection of transmission wiring between
indoor-outdoor units and outdoor-outdoor units
Defective indoor unit PCB
Defective outdoor unit PCB
V V V
UJ Malfunction of transmission
(accessory device)
Defect of accessory devices
Faulty wiring
V V V V V
60 External protection device
activated (Heat reclaim ventilator)
Actuation of external protection device
Defective output signal wiring
Defective control PCB
V
64 Malfunction of indoor air thermistor
(Heat reclaim ventilator
Defective connector contact
Defective indoor air thermistor
Defective control PCB
V
65 Malfunction of outdoor air
thermistor (Heat reclaim ventilator)
V
6A Malfunction of damper system
(Heat reclaim ventilator)
Defective connector contact
Defective limit switch
Defective damper motor
Defective control PCB
V
70 System No. 2
Compressor overheat
Shortage of refrigerant amount
Defective connector contact
Leakage of four way valve
V
71 System No. 2
Compressor overcurrent
Shortage of refrigerant amount
Short circuit
Defective compressor
V
72 System No. 2
Fan motor overcurrent
Defective fan motor connector contact
Defective fan motor
Defective PCB
V
73 System No. 2
Actuation of high pressure switch
(HPS)
Dirty heat exchanger
Shortage of water volume
Clogged refrigerant piping
Defective connector contact
Defective HPS
V
74 System No. 2
Actuation of low pressure switch
(LPS)
Clogged refrigerant piping
Defective connector contact
Shortage of gas
Defective LPS
V
75 System No. 2
Malfunction of low pressure sensor
Defective connector contact
Defective low pressure sensor
Defective PCB
V
76 System No. 2
Malfunction of high pressure
sensor
Defective connector contact
Defective high pressure sensor
Defective PCB
V
77 System No. 1
Malfunction of fan inter lock
Defective relay contact
Broken wire
V
78 System No. 2
Malfunction of fan inter lock
Defective relay contact
Broken wire
V
7A System No. 2
Malfunction of compressor current
sensor
Defective current sensor
Defective compressor
Defective outdoor unit PCB
V
7C System No. 2
Malfunction of pump inter lock
Cooling water pump interlock actuated V
80 Malfunction of entering water
temperature thermistor
Defective connector contact

Defective entering water temperature thermistor

V
81 Malfunction of leaving water
temperature thermistor or drain
pipe heater
Defective connector contact
Defective leaving water temperature thermistor
V
82 System No. 1
Malfunction of refrigerant
thermisto
Defective connector contact
Defective refrigerant thermistor
V
83 System No. 2
Malfunction of refrigerant
thermistor
Defective connector contact
Defective refrigerant thermistor
V
84 System No. 1
Malfunction of heat exchanger
thermistor
Defective connector contact
Defective heat exchanger thermistor
V
85 System No. 2
Malfunction of heat exchanger
thermistor
Defective connector contact
Defective heat exchanger thermistor
V
86 System No. 1
Malfunction of discharge pipe
thermistor
Defective connecting connector
Defective discharge pipe thermistor
V
88 System No. 2
Malfunction of discharge pipe
temperature
Shortage of gas
Defective discharge pipe thermistor
Defective connector contact
Clogged refrigerant piping
V
89 Malfunction of brazed-plate heat
exchanger freezing
Dirty heat exchanger
Shortage of refrigerant amount
Defective thermistor
V
8A System No. 2
Malfunction of leaving water
temperature thermistor
Defective connector contact
Defective leaving water temperature thermistor
V
8E System No. 1
Malfunction of suction pipe
thermistor 1 for heating
Defective connector contact
Defective suction pipe thermistor
V
8F System No. 1
Malfunction of suction pipe
thermistor 2 for heating
Defective connector contact
Defective suction pipe thermistor
V
8H Abnormal hot water high
temperature
Three way valve malfunction
Defective thermistor
Defect of water temperature setting
V
90 Abnormal chilled water quantity or
abnormal AXP
Shortage of water volume
Disconnection of AXP
V
91 Defective connector contact
Defective electronic expansion valve coil
V
92 System No. 2
Malfunction of suction pipe
thermistor
Defective connector contact
Defective suction pipe thermistor
V
94 Malfunction of transmission
(between heat reclaim ventilator
and fan unit)
Defective fan unit PCB
Defective connecting wire between (1) and (2)
V
95 System No. 1
Malfunction of inverter system
Defective fan inverter unit V
96 System No. 2
Malfunction of inverter system
Defective fan inverter unit V
97 Malfunction of thermal storage unit Defective thermal storage unit V
98 Malfunction of thermal storage
brine pump
Actuation of thermal storage brine pump overcurrent (OC) V
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ
AJ